Dacia Sandero

Using information from the 1 camera, the function triggers corrective action on the vehicle steering system when a continuous or broken line is crossed or when approaching the roadside (divider, barrier, pavement, embankment, etc.) without activating the direction indicator lights.

Depending on the setting, in the event of crossing a broken line without activating the direction indicator lights, the function:

• warns the driver without corrective action on the steering system;

or

• performs corrective action on the steering system.

Location of the camera 1

Make sure the windscreen is not obscured (by dirt, mud, snow, condensation etc.).

Activation/deactivation

Operation

When the function is activated, the warning light is displayed in grey on the instrument panel and the left-hand and right-hand line indicators 8 are displayed in grey on the instrument panel.

The function is set to notify or react if:

• the speed is between about 40 mph (65 km/h) and 105 mph (170 km/h);
• the warning light is displayed in white and the left-hand or right-hand line indicators 8 are displayed in white on the instrument panel.

The function is in operation if the vehicle:

• approaches a roadside without activating the direction indicators;
• crosses a continuous line without activating the direction indicators;
• crosses a broken line without activating the direction indicators, if the "Operation on broken line" setting is selected.

In these cases:

• the function triggers an action on the vehicle's steering system to correct the vehicle trajectory;

and

• the warning light flashes white or, depending on the vehicle, the warning light is displayed in yellow and the indicator 8 on the side of the breached line is displayed in yellow on the instrument panel.

In certain cases, if the corrective action taken on the steering system is not sufficient, the warning light will continue to flash in white or, depending on the vehicle, the warning light is displayed in red and the indicator light 8 on the side of the breached line changes to red on the instrument panel. This is accompanied by a vibration on the steering wheel.

When the "Operation on broken line" setting is not selected, the function sounds the alarm if the vehicle crosses a broken line without activating the direction indicator lights, and there is no roadside close enough to the line.

In this case, the function warns the driver:

• by a vibration in the steering wheel;

and

• the warning light flashes white or depending on the vehicle, the warning light is displayed in red and the indicator 8 on the side of the breached line turns red on the instrument panel.

Note: on bends, the function allows for slightly cutting the bend.

Special cases

"Keep control" alert.

• If the system is operating and does not detect any activity on the steering wheel, the "Keep control" message appears on the instrument panel accompanied by a beep and, depending on the vehicle, the warning light appears in yellow until the driver has regained control of the vehicle.

or

• If the system has been in operation for too long, the message "Keep control" appears on the instrument panel accompanied by a sound alert and, depending on the vehicle, the warning light in yellow and the indicator 8 on the side of the line concerned flashing until the driver has regained control of the vehicle.

Function temporarily unavailable/disabled

The function is temporarily unavailable or disabled in the following cases:

• very fast lane departure;
• driving continuously on a line;
• approximately four seconds after changing lanes;
• tight bends;
• impaired visibility;
• one of the direction indicators is activated;
• activating the hazard warning lights;
• engaging reverse gear;
• strong acceleration;
• the lane width changes;
• operation of the electronic stability control ESC;
• operation of the anti-lock braking system.
• the active emergency braking system is triggered;

If the front camera is obscured, the "Front camera no visibility" message is displayed on the instrument panel.

Clean the area where the sensors are located.

Automatic deactivation

The function is automatically deactivated when:

• the electronic stability control ESC is deactivated or malfunctions;
• the anti-lock braking system is malfunctioning;
• A towbar is electrically connected to the trailer hitch socket;
• the warning light is displayed.

When the function is deactivated, depending on the vehicle, the warning light is displayed in yellow or white on the instrument panel, or the warning light disappears from the instrument panel.

Settings

Vehicle fitted with a multimedia screen 3

To access the multimedia screen function settings 3, refer to the multimedia instructions:

• "Operation on broken lines": use this setting to select the response of the function if the vehicle crosses a broken line without one of the direction indicators having been activated:
  • selected setting: the function may trigger an action on the vehicle's steering system to correct the vehicle trajectory;
  • setting not selected: the function can warn the driver by means of a vibration at the steering wheel without correcting the vehicle trajectory.
• "VIBRATION": adjust the steering wheel vibration for the "Lane departure prevention" function;
• depending on the vehicle, "Lane exit anticipation" or "Warning": adjust the line detection sensitivity level. To do this, select:
  • "Late": line detected upon crossing;
  • “Standard”: line detected on approach;
  • "Early" line detected nearby.

Please refer to the multimedia instructions for further information.

Vehicle not fitted with a multimedia screen

(depending on the vehicle)

• With the vehicle stationary, press the switch 4 as many times as required to reach the  tab;

or

• press switch 4 and repeatedly press control 5 or 6 to reach the  tab;
• press the 7 "OK" switch
• repeatedly press control 5 or 6 to reach the menu, then press the 7 "OK" switch;
• repeatedly press control 5 or 6 to reach the "DRIVING ASSIST" menu, then press the 7 "OK" switch;
• repeatedly press control 5 or 6 to reach the "Lane Keep Assist sensitivity" menu, then press the 7 "OK" switch;
• repeatedly press control 5 or 6 to select the setting, then press on switch 7 "OK".

Operating faults

When the system detects an operating fault:

• the warning light is displayed in yellow or in white on the instrument panel;

or, depending on the vehicle

• the warning light is displayed on the instrument panel.

In some cases, they are accompanied by:

• the "Driving assist unavailable" message;

or

• the "Check Driving assist" message;

or

• the "Check Front camera" message.

In these cases, please contact an approved dealer.

Warnings