Dacia Bigster
Front headlights: replacing the bulbs
Main beam headlight 1
(depending on the vehicle)
Remove the cover A.
Unclip the connector 2, remove the assembly from its housing and take out the bulb.
Bulb type: H7.
Before replacing the bulb, make a careful note of its position in its housing. After changing it, check that the replacement bulb is in exactly the same position in the housing. Clip the cover in place.
Dipped beam headlight 3 ( LED )
(depending on the vehicle)
Consult an approved Dealer.
Daytime running light/side light 4 ( LED )
(depending on the vehicle)
Consult an approved Dealer.
Direction indicator light 5 ( LED )
(depending on the vehicle)
Consult an approved Dealer.
warning
Please note when working close to the engine that it may be hot. The engine cooling fan may also start at any moment. The
label in the engine compartment reminds you of this.
Risk of injury.
Rear lights: changing bulbs
Direction indicator lights / brake and side lights
Open the tailgate and remove the cover A.
Unscrew the nut 1 and take out the light unit 2 from the outside.
Release the connector 3 and unlock the clips 4 to remove the bulb holder 5.
tip
To comply with current legislation, or as a precaution, you can obtain an emergency kit from your approved dealer containing a set of spare bulbs and fuses.
warning
The bulbs are under pressure and may break when replaced.
Risk of injury.
Brake light 6 with LED
Side light 7 with LED
Direction indicator light 8
Bulb type: WY16W.
warning
Do not touch the exhaust.
Risk of burns.
Refitting
To re-fit, proceed in the reverse order taking care not to damage the wiring, tighten nut 1 first.
Reversing light9
(depending on the vehicle)
Access the bulb holder located underneath the rear bumper, then unscrew it by rotating it towards the exterior of the vehicle and remove the bulb.
Bulb type: P21W.
Refitting
To refit, proceed in the reverse order, taking care not to damage the wiring. Once the bulb has been replaced, check that it is properly secured.
However, because of their reduced accessibility, we advise you to have your bulbs replaced by an approved Dealer.
High-level brake light 10 with LED
Consult an approved Dealer.
Number plate light 11 (LED)
(depending on the vehicle)
Consult an approved Dealer.
warning
The bulbs are under pressure and may break when replaced.
Risk of injury.
Fog lights: changing bulbs
Front fog lights 1 LED
Consult an approved Dealer.
Rear fog light 2
(depending on the vehicle)
Access the bulb holder located under the rear bumper, then unscrew it by turning towards the centre of the vehicle and remove the bulb.
Bulb type: P21W.
warning
Do not touch the exhaust.
Risk of burns.
tip
To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an approved dealer.
warning
Please note when working close to the engine that it may be hot. The engine cooling fan may also start at any moment. The
label in the engine compartment reminds you of this.
Risk of injury.
Refitting
To refit, proceed in the reverse order, taking care not to damage the wiring.
Once the bulb has been replaced, check that it is properly secured.
However, because of their reduced accessibility, we advise you to have your bulbs replaced by an approved Dealer.
warning
The bulbs are under pressure and may break when replaced.
Risk of injury.
warning
Any operation on (or modification to) the electrical system must be performed by an approved Dealer since an incorrect connection might damage the electrical equipment (harness, components and in particular the alternator). In addition, your Dealer has all the parts required for fitting these units.
Indicator lights: changing bulbs
As the door mirror shell needs to be removed, we advise you to have the bulb replaced by an approved dealer.
To access the bulb:
- carefully unclip the door mirror shell 2 from its base 3 (movement A);
- unclip the shell 4 using a flat-blade screwdriver or similar (movement B);
- unscrew the screws 5 using a screwdriver;
- unclip the cover 6 of the repeater 1 to access the lamp;
- turn the lamp holder 7 and pull out the bulb 8.
Bulb type: WY5W.
To refit it, carry out the above operations in reverse order.
Make sure:
- that the bulb holder 7 is aligned correctly before inserting it into its housing;
- that the door mirror shell 2 clips properly onto its base 3.
When disassembling and refitting, ensure that the wiring and the surrounding components are not damaged.
warning
The bulbs are under pressure and may break when replaced.
Risk of injury.